Meet us next:   NIH Research Festival 2024  24 September  •  Safety Pharmacology Society 2024  22-24 September  •  Drug Discovery 2024 - ELRIG  2-3 October  •  The Cell & Gene Meeting on the Mesa 2024  7-9 October (in person) & 10-11 October (virtual)  •  Other upcoming events
Protocol:

Media Volumes Guide for Different Feeding Options in Alvetex® Scaffold in Well Insert Formats

● Download this protocol as a PDF (1 MB)

1. Introduction

Alvetex Scaffold inserts are currently available in the following formats; 12 well inserts (AVP005) and 6 well inserts (AVP004), suitable for longer-term and co-culture experiments and air/liquid interface set-ups. Inserts are compatible with standard tissue culture plates and with REPROCELL’s well insert holder in a deep Petri dish (AVP015), designed for demanding cell types to provide increased volumes of culture media. 12 well inserts fit into both 6- and 12 well plates (to fit into 12 well plates the extended arms must be snapped off). When deciding which Alvetex Scaffold format to use, the following factors should be considered in combination:

  • Cell type and duration of experiment,
  • The desired depth of cell penetration into the 3D scaffold,
  • The type of assay or end point analysis to be performed.

For Advice on Alvetex handling prior to use, cell seeding densities and monitoring of cell attachment for all available inserts and plate formats, please refer to our Alvetex Scaffold Quick Start protocol.

2. Media volumes guide

Alvetex inserts have been designed to allow for three media feeding options, each suited to different 3D culture applications as described in Figure 1. A guide to the volume of media required both inside and outside the insert is presented in Table 1 for each feeding option and both 6 well inserts (AVP004) and 12 well insert (AVP005) formats.

PR-ALVETEX-SCAFFOLD-D056_fig-01a

(i.) Media from below only
for cells grown in 3D at air-liquid interface.

 PR-ALVETEX-SCAFFOLD-D056_fig-01b

(ii.) Media from above and below
for routine 3D growth of cells with lower-average metabolic activity/proliferation rate OR for experiments where cells are incubated with test substrate in top chamber only for permeability investigations.

 PR-ALVETEX-SCAFFOLD-D056_fig-01c

(iii.) Media interconnected
for routine 3D growth of cells with high metabolic activity/ proliferation rate.

Figure 1. Media filling levels and well insert configurations.

Using Alvetex Scaffold
well inserts		 Media volumes for different feeding options
(i) Media from
below only		 (ii) Media from
above and below		 (iii) Media
interconnected
Insert Well Insert Well Insert Well
24 well insert (AVP012)
in 24 well plate		 None 0.8 mL
to 1 mL		 < 0.4 mL 0.8 mL
to-1 mL		 > 0.4 mL 1.8 mL
to 2.3 mL
24 well insert (AVP012)
in 12 well plate		 None 1.5 mL
to 2.5 mL		 < 0.4 mL 1.5 mL
to 2.5 mL		 > 0.4 mL 3.5 mL
to 4.5 mL
12 well insert (AVP005)
in 12 well plate		 None 1.5 mL
to 1.8 mL		 < 0.5 mL 1.5 mL
to 1.8 mL		 > 0.5 mL 3.5 mL
to 4.5 mL
12 well insert (AVP005)
in 6 well plate		 None 3.6 mL
to 5.5 mL		 < 0.5 mL 3.6 mL
to 5.5 mL		 > 0.5 mL 8.5 mL
to 11 mL
6 well insert (AVP004)
in 6 well plate		 None 3.6 mL
to 5 mL		 < 1.1 mL 3.6 mL
to 5 mL		 > 1.1mL 8.5 mL
to 11 mL

Table 1. Media volumes for different Alvetex Scaffold feeding options. For (1.) Media from below only, the insert should just be in contact with the media below. Volumes are approximate and will need to be adjusted by the end user.

Contents